What is the most important thing to do in transportation? Of course, the quality of trucks is the most important! Then where is the most important factor in choosing cars? Hubei users Zhang Luokun, who has more than ten years of truck driving experience, will definitely tell you that the engine is the most important. In his view, choosing a suitable engine to buy a car is half successful. The selection stems from the trust Shaanxi Automotive Cummins continues to accompany Zhang Luokun has been wandering in trucks for more than a dozen years. He knows very well about trucks. Among them, Shaanxi Automobile Truck Co., Ltd. is the most contacted truck. At present, Master Zhang is already using the 7th Shaanxi Auto Truck. The reason why Shaanxi Trucks is more and more reliant on trucks is that in addition to the quality of Shaanxi Trucks, the most important point is that The steam truck was equipped with a Xi'an Cummins transmitter. "As early as five years ago, I began to contact Xi'an Cummins Engine. At that time, the car I bought was Xikang's machine. The quality was good. Later, I sold the car. It is understood that the person who is currently buying the car is still using it. You see how good the quality is!†Talking about Xikang’s engine, Master Zhang is already deeply impressed. So when the car was changed last year, Master Zhang also chose Shaanxi Automobile Cummins Trucks. Currently, the truck has traveled 25,000 kilometers and there have been no failures. The most optimistic view of Master Zhang is the adaptability of the Xikang engine. It turned out that when the car was first purchased, Master Zhang was prepared to transport Hubei to Harbin. However, after the car was purchased, it was changed to the transportation route from Chongqing to Chengdu. Compared with the Harbin section, the road conditions from Chongqing to Chengdu are more complicated, with more mountainous roads and hills. At first, he was worried that the power of the Xikang engine was not enough. Actually, Master Zhang really felt that he had earned it. “Chongqing Road has more mountainous roads and there are some places where we can climb. Each vehicle is also transporting 31-32 tons. Although it is not heavy, there is still demand for power uphill. At the beginning, I was concerned that the engine power was insufficient, but there was no The 385 engine that I thought of purchased had no problem with climbing, and it was quick to start. It also had a brake that could be installed. It was safer to turn downhill.†Master Zhang said with a smile, especially the Boke brake, when it was bought five years ago It is fancy it. Economic energy-saving wealth is a good helper Xikang engines are not only powerful but also economically advantageous. Master Zhang simply calculated an account for us. Despite the fact that it has not been used in the near future, there is no definitive data on the fuel consumption, but the advantages of the engine have begun to show. Master Zhang said that at present, according to the engine oil meter calculation, the oil fee is 3.08 yuan per kilometer, according to the actual fuel volume is 3.2 yuan per kilometer of oil. “Compared to the engine I originally used, it is definitely fuel-efficient. If you use a 3-meter trailer, you may still be more fuel-efficient. It is estimated that it is about 2.8 yuan per kilometer. Although one kilometer is the difference between a few cents, it will always be There are tens of thousands of kilometers of travel mileage, which can save thousands or even tens of thousands.†Master Zhang also said that the configuration of Auman’s GTL’s Xikang machine has been heard to be more fuel-efficient! At the same time, Master Zhang stated that he was very relieved. After using it for a long time, Master Zhang's engine had undergone two maintenances. The first time he had traveled 3,000 kilometers, the second time he had been driving 12,000 kilometers, or 15,000 kilometers, again. “The next time we do maintenance, we will drive to 30,000 kilometers. According to this situation, it will be easier and easier to maintain.†Master Zhang is very satisfied with the maintenance situation. Master Zhang also mentioned that Xikang's after-sales service is very good. Xikang promises that the basic parts will be limited to 36 months of unlimited warranty, important parts 24 months unlimited mileage warranty, there is no worries. It is gratifying that after-sales staff are also very enthusiastic about users and their service attitude is very good. It is much better than the engine brand he used before. In addition, Master Zhang also said that truck users are mostly word-of-mouth. After his use recommendations, many people have started to buy Xikang engines. Everyone is equally praised. The so-called alone music is not as good as the music and music. Master Zhang also suggested that companies should increase their propaganda, so that all users can understand and understand the Xikang engine as a good machine, so that the engine's good quality can serve more users. Now, Master Zhang's transportation business is getting more and more prosperous. In the later period, he intends to purchase 4 more cars. "I will choose Xi'an Cummins Engine next time I buy a car!" I expect more users like Master Zhang to join the Xikang engine family.
Titanium alloy is mainly used to make aircraft engine compressor parts, followed by rocket, missile and high-speed aircraft structural parts.By the mid-1960s, titanium and its alloys had been used in general industry to make electrodes for the electrolytic industry, condensers for power stations, heaters for oil refining and desalination of seawater, and environmental pollution control devices.Titanium and its alloys have become corrosion resistant structural materials.It is also used to produce hydrogen storage materials and shape memory alloys.
Titanium Parts is the use of cnc machining out, including: drilling, boring, cutting, turning, screw. Product material titanium alloy .In the high-speed machining out of the workpiece has a good finish. cnc machining products surface treatment has laser engraving LOGO, powder coating,brushing, rolling flower, according to the special requirements of the drawings.We have a special inspection department to carry out inspection, to ensure that each size of products meet the requirements of the drawings,CNC Machining Parts is the most common in mechanical processing, low density, not easy deformation, high precision products.
CNC Machining Titanium Parts,Titanium Parts,Cnc Turning Machining Titanium Parts,CNC Turning Titanium Parts YaoPeng Metal Products Co., Ltd. , http://www.ypmfg.com
Xi'an Cummins Engine