At 9:58 on September 18, the ignition of the CA6DLD-30E4 two-stage supercharged diesel engine was successfully held in Xichai. Dong Chunbo, deputy general manager of FAW Group Corporation, successfully ignited the CA6DLD-30E4 two-stage supercharged diesel engine prototype. FAW Group's CA6DM project commander Wang Zhenkun, general manager of FAW Jiefang Co., Ltd. Wang Lizhi, relevant leaders of the xicai factory and related leaders and technicians of the research and development department attended the lighting ceremony. The lighting ceremony was presided over by Cai Zhenfa, secretary of the party committee of the factory. Dong Chunbo, deputy general manager of FAW Group Corporation, gave a warm speech and fully affirmed the successful ignition of the CA6DLD-30E4 two-stage supercharged diesel engine of Xichai. He thanked Xichai for its wide range of technicians. This made a positive contribution and sincerely wished Xiechai to build a factory for the sixty-sixth anniversary and the new factory gate will be completed in double happiness. The CA6DLD-30E4 diesel engine is the first two-stage supercharged diesel engine independently developed by Xichai. This engine has a displacement of 6.6L, a rated speed of 2300 rpm, a rated power of 220 kilowatts, a maximum torque of 1,100 Nm, a wide range of maximum torque speeds, and a torque of 750 Nm for 800 turns. This engine uses a 1800-bar high-pressure common-rail fuel injection system. Cooled EGR is used as the main technical route for emission control. The booster system uses a two-stage supercharger. The maximum explosion pressure of the engine is 180 bar, and the emissions meet the national regulatory standards. CA6DLD-30E4 diesel engine adopts two-stage supercharging technology and has four obvious advantages. First, it has high power density and obvious light weight characteristics. Second, it has low emission and low fuel consumption. It is 2 to 3% lower than the equivalent diesel engine fuel consumption, and carbon dioxide emission is reduced. It is more green and environmentally friendly. Third, it is quicker to respond quickly. As the fresh air enters the cylinder after being pressurized in two stages, the acceleration response performance is greatly improved. Fourth, the cost is low. After the two-stage booster technology is used, the smoke of the engine is greatly reduced. The particle emission is up to the fourth national standard, the post-processing system can be eliminated, the vehicle cost is greatly reduced, at the same time, the engine use is not subject to fuel quality limits, and geographical adaptability is also greatly increased. Dong Chunbo said that the 6,000 units of the Xichai CA6DL diesel engine are now available for the Liberation of Denway, the liberation of the unicorn and other models . This will not only generate benefits, but also lay a solid foundation for future development. I am very excited to participate in the ignition ceremony of the CA6DLD-30E4 two-stage supercharged diesel engine today. The two-stage turbocharged diesel engine is currently applied in only a few European and American countries in the world, and it has an international leading level. It is the first application in China. At the same time, Dong Chunbo also hopes that Xichai will continue its efforts to install the CA6DLD-30E4 two-stage supercharged diesel engine on the liberation car as soon as possible to further strengthen the liberation and self-reliance of confidence, and to assume its own important responsibilities and make new and greater contributions. Longlived 430 Stainless Steel Cut Wire Shot are all produced through German craftsmanship with bright, defect-free and pollution-free material. After strict processing like heat treating, wire drawing, electronic spiral cutting, passivation molding and other processes, our products are strictly in a accordance with German Spring Association standard VDFI8001, German industrial standards DIN8201 and American Aerospace Material Specification Standard. It is widely used for surface shot blasting, sand blasting and shot blasting of stainless steel parts, aluminum alloy die castings, and copper alloy parts. According to different composition, stainless steel is classfied several grades such as 304, 410, 430, 201 and 430 stainless steel Cut Wire Shot is the most popular abrasive of them as its excellent performance. The composition of 430 stainless steeel is: C≤0.12, Cr 16.00-18.00, Ni 0, Mn ≤1.25, P≤0.035, S≤0.030, Si≤0.75. So you can check if 430 Stainless Steel Shot could meet your requirement. Generally 430 stainless tseel cut wire shot could be classfied two kinds. One is as cut and the other is conditioned. Compared with as cut one, conditioned is without sharpe edges and corners and has near round shape. According to this, you can choose the more suitable one. 430 Stainless Steel Shot,Resistance Stainless Steel Shot,Sus430 Stainless Steel Cut Wire Shot,Ss430 Stainless Steel Cut Wire Shot Longlived Metal Products Co ., Ltd , https://www.stainlesssteelshotcn.com