The breeding of small grain crops such as wolfberry fruit and millet is an arduous and meticulous task, and it is also crucial for the indoor test. Taking millet as an example, the most difficult and important one is the one-thousand-grain weight and the out-rice rate, which means that it takes time and effort, and it is also easy to make mistakes. After many years of exploration, we have developed a set of time-saving, effortless and scientific methods that are proposed for reference by colleagues and wish to provide valuable suggestions. The role of automatic seed test analysis and the 1000-grain weight system in this work cannot be ignored. Add WeChat more and more professional just waiting for you to come:
Froth pumps are the latest generation of foam pump/froth pump based on the advanced technology at home and abroad, including foam tank froth Slurry Pump, high pressure slurry pump. It could eliminate the foam/froth in the slurry in running and work normally even if the feeding slurry is not enough. Froth pump is the ideal products to deliver the frothy slurry, especially in the flotation technique process.
Slurry Froth Pump,Froth Foam Pump,Centrifugal Froth Pump,Foam Tank Froth Slurry Pump,
High Pressure Slurry Pump Shijiazhuang Boda Industrial Pump Co., Ltd. , https://www.mineralslurrypump.com
Regarding the 1,000-grain weight: As the grain size is small, it takes a lot of effort to count, and after each 1000 grains are counted, it is often an error. Later, the container filling method was used to increase labor efficiency by a factor of 100. That is, with a 2.0 to 2.5 ml disposable plastic tube syringe, one end of the needle tip was cut into a tube shape and flattened. Thousands of grains were loaded into the tube and the piston was moved so that the grain was flush with the nozzle and the piston scale was fixed. Refill the millet with 100 grains. After multiple determinations, the error of one hundred grains does not exceed three, and the total error is negligible. It should be noted that the plastic tube can not be too thick or too thin, too thick will increase the error, too thin and difficult to fill.
Later, we studied and adopted the semi-processing band calculation method to solve this problem easily. The method is: first weigh out 10g of sample millet, remove rice by hand, remove some part of the hull, remove the worm, measure the weight of processed grain and rice, and then evenly sample 200 grains. Examples of the percentage of valleys and rice. Note that sampling must be representative. If the rice mix weight is mg, check the number of millet grains per 100 grain is p grain, millet grains q grain, set the weight of the original 10 grams of sample millet millet weight is x grams, the weight of the pot is y grams, then, Based on the above known conditions, the following equation can be derived from the equation: X = (100m - 10q) ÷ p. If the sample taken is not 10 grams, but z grams, the relationship is: x=(100m-zq)÷p. Where: z, m, p, q are all known numbers.
For example: take 10 grams of millet, after rough processing to remove 7 grams of coarse rice left, remove 200 from the rough rice, check the number of millet grains accounted for 80, 20% of the grains accounted for, that is z = 10, m = 7 , p=80, q=20. Substituting for x=6.3 (grams), that is, the rice output rate is 63%. The rice rate measured by this method is obviously closer to reality than the actual rice output rate of actually peeled millet. Because this method can avoid the mechanical damage and loss in the process, it can save labor, labor, science, and easy operation. The automatic seed test analysis and the application of the 1000-grain-heavy instrument system have changed the status and provided more accurate help. 
Features of Foam/Froth Pumps
1. On the bearing house, there is the motor base or motor support, which helps adopt belt drive or direct drive. It is very convenient to change the pulleys to adjust the speed and meet the changes of the work conditions.
2.The box is made of steel, stainless steel or rubber lined steel. It has the feeding suction and overflow box in the tangent line. The overflow box could deliver the surplus slurry back to the pool. The feeding suction in the tangent line could transport the slurry fast and eliminate part of the froth.
3. Froth pumps are of double-casing. The materials of the wet parts could be metal alloy, rubber or other non-metal material according to the slurry properties.
Application of Froth Pumps
It is used widely in the metallurgy, minerals, coal washery, chemical and other industrial departments, suitable for handing the abrasive and corrosive slurry with the froth.
