The use of cars has occupied our lives. When we use them, how do we deal with some unexpected situations? Let Xiao Bian introduce the relevant reason analysis about the car water temperature warning light. First, the water temperature alarm lights There are two possible causes of the water temperature alarm light. The first possibility is that the fan has stopped. At this time, we only need to open the cover of the car to check if the fan is stuck or the plug is off. The second possibility is the thermostat or the pump is wasted. At this time, we can touch down the water pipe and feel whether the water temperature is cold. If the water temperature is cold, it proves that the thermostat or the water pump is wasted, and the coolant cannot be circulated. When it is found that the water temperature warning light is on, we must stop by the parking lot to find out the reason and open the cover to assist in heat dissipation. If necessary, we must call the rescue vehicle and we must not try to launch the car again. Otherwise, the consequences would be unimaginable. Second, the water temperature lights There are also two reasons why the water temperature indicator of the water tank is on, which is divided into leakage of coolant and internal leakage. To judge whether the coolant leaks out, we can check whether there is any leaking liquid in the lower guard plate or the floor under the car, because the coolant is not only difficult to evaporate at normal temperature, but also has color. Therefore, even if the cabin is originally wet, we can judge it. The second case is internal leakage. If there is no external leakage, it is very likely that the cylinder mattress is damaged, causing the coolant to enter the cylinder and the oil passage. Fortunately, these two conditions are not terribly terrible. Adhering to a nearby maintenance facility should not be a problem, but our car must be inevitably overhauled. The above is the analysis of Xiao Bian's alarm related to the car tank lights, hoping to bring some help to the owners. When encountering this kind of situation, they can quickly make correct judgments and reduce the damage of the car as much as possible. To the lowest. Scrap crusher is a kind of crushing machine used to produce scrap material, mainly used to scrap cars, scrap appliances and light scrap steel machine.
6. Power consumption per ton of molten steel is reduced.
Energy needs:
The structural characteristics of the crusher are roughly as follows: Scrap Steel Crusher, Steel Crusher Shuangxing Mechanical Equipment Co.,Ltd , https://www.gyshuangxing.com
Scrap crusher after the crushing treatment of scrap has the following characteristics:
1. Neat material shape and similar specifications;
2. High bulk density;
3. Less attachments;
4. High purity.
The advantages of using broken steel for steel smelting are as follows:
1. High yield;
2. The chemical composition of molten steel is stable and the content of sulfur and phosphorus is low;
3. Shorten smelting cycle;
4, furnace lining life extension;
5. Reduce air pollution and slag;
The effective recovery and utilization of scrap metal resources can greatly reduce the exploitation and consumption of natural mineral resources, so as to reduce land occupation, reduce total energy consumption, save investment, protect the ecological environment and improve labor production benefits. Especially in the extreme consumption of natural mineral resources and increasingly scarce today, scrap metal resources in the world economy. The position of sustainable development strategy is more and more prominent. Since 2000, all countries in the world have been actively and effectively recycling scrap metal resources, in order to properly curb the long-term transition of mineral resources and energy consumption. Scrap iron and steel is the only raw material that can replace iron ore in the production of iron and steel.
1) the shell of the main engine is made of extra thick steel plate with a high manganese cast steel lining, which can be replaced;
2) there are 11 steel discs mounted on the horizontal shaft in the rotor of the main engine. There are 6 pin shafts distributed around the circumference of the steel disc and 10 hammer heads suspended in the axial direction.
3) the spindle is supported by ball bearing, and the circulating oil is forced to lubricate and cool, and equipped with temperature sensor;
4) the feeding port is equipped with super strong double-barrel feeding device, which is rotated in the same direction, and can gradually flatten the large loose materials and feed them into the machine. The speed of the drum determines the feeding speed, which is controlled by the motor load current feedback of the host, realizing automatic regulation to ensure that the host is in the best load state.
5) after the unbreakable material enters the machine, the operator can open the discharge door to discharge it from the machine to avoid damage to the crusher.
The working principle:
Scrap crushing processing is the use of crusher scrap crushing, the use of sorting system after the broken scrap separation to get pure high quality scrap processing method. Its working principle is that under the continuous drive of high speed and large torque motor, the hammer head on the rotor of the crusher takes turns to strike into the cavity scrap, under the strong impact, scrap is torn and squeezed into a certain size of broken steel, and then through the sorting equipment processing, you can get high purity quality broken steel.