First aid method for damage to garbage truck chassis: Garbage trucks are used frequently. Whether it is windy or rainy, they must work. The chances of chassis damage are relatively large. In the winter, it is necessary to thoroughly clean the chassis and prevent rust. First of all, the chassis should be thoroughly cleaned. If there is too much mud on the chassis, it must be washed again with an oil-removing detergent to expose the chassis to the original “natural†color so that the rust preventive care can be started. In a professional beauty shop, the car can be lifted to a lifting rack for chassis cleaning, wiping, and rust prevention. In the middle of this should pay attention to, after the cleaning must be sure to wait until the water on the plate after the dry, in order to carry out anti-rust care. When performing care, be sure to maintain a uniform spray coating to form a durable layer of uniform anti-rust coating. After the completion of all the natural air drying 5-10 minutes, the chassis rust treatment is completed. After the professional chassis care is done, it does not mean that it is completely foolproof. There is a misunderstanding that people often wash the car by themselves in order to love the car, and often add some detergents. Please be careful not to use alkalinity. Cleaner, washing powder, etc. Rinse the body and chassis, otherwise it will affect the anti-rust effect and shorten the anti-rust time. It is recommended that the owner go to a professional beauty shop to do card care. There is a simple way to check out the quality of the car. After the high-pressure water jet washing, the chassis of the anti-rust care is almost not hung. This effect means that it is genuine. Care can play a very good rust protection effect. Vehicle chassis damage first-aid When the vehicle is damaged in the chassis in the field or far from the vehicle repair location, the following emergency methods can be used to drive the vehicle to the conditions for repairing the vehicle in response to different fault conditions. Brake cylinder leakage brake fluid or the branch pipeline broken, can be used in the branch of the pump pipe with tin, copper skin to be a small mat, block the pipeline, and then tighten the screws, or the fracture flat, The curling is blocked, so that the wheel can not be used as a brake. However, doing so may cause unilateral braking, and should pay attention to safety when driving. The brake master cylinder lacks brake fluid and can be replaced by alcohol or liquor. In special cases, fresh water can be used instead. Brake cups rise and the soaked skin cups are soaked in hot water for 10 minutes to 20 minutes to remove the oily components from the bowl so that the cups can be restored to their original size. The clutch friction plate is ablated and slippery, and the friction plate that is less severe for ablation can be turned over. If the ablation is severe, use several layers of cotton cloth or canvas (the thickness of which should be the same as the original friction plate), and use steel wire or wire to pass through the hole in the steel plate to fix it. When driving a vehicle, it should be done steadily and the gear shifts quickly. The tie rod ball joint is broken. In the bumper or other places that do not affect the driving, remove a screw with a total length similar to the ball joint to replace the broken ball joint. After installing the knuckle arm and nut, expose the screw. Partially riveted with a hammer. Damage to the triaxial automobile differential gear, such as damage to the differential in the rear axle, can be removed from the bridge driveshaft and axles, and continue driving. If the front differential is damaged, remove the hub splint and continue driving 5 Diameters 4.0mm-- 20.0mm Carbide Drill Bit Coolant
5 Diameters 4.0mm-- 20.0mm Carbide Drill Bit Coolant
The inner hole bit, also known as the core bit or hole saw, is a tool like Swiss Type Automatic Lathe, CNC Lathe and Cnc Slitting Automatic Lathe used to drill holes in various materials such as wood, metal, concrete and stone. They are hollow cylinders with teeth or cutting edges on the outer surface. The inside of the drill bit is hollow and the drilling material can be removed from the center of the drill bit. Drilling bits coolant Ningbo Leyan Machinery Technology Co., Ltd , https://www.cncleyan.com
In-hole drill bits are commonly used in construction, plumbing, electrical engineering, and other industries that require accurate, clean holes. They come in a variety of sizes and can be used with hand drills, drill presses or other drilling machines.
They can be used for a variety of purposes, such as opening holes for pipes, cables or wires, installing hardware or fixtures, opening holes for ventilation or electrical outlets, or for general woodworking or metalworking tasks.