The granulator machine can make granules from wet powder materials or break down the dry lumpish material, which is widely used by the industries of pharmacy, chemical and foodstuff. By driving of mechanism, the cylinderis swinging to-and-fro to force the target material squeezed from sieveto make out granules or to smash it as granules. This granulation machine is made of stainless steel, in line with GMP standards. Granulator Machine,Pelletizer machine,Pelletizing Machine,Dry Granulator,Granulation Machine JIANGYIN CITY XUAN TENG MACHINERY EQUIPMENT CO.,LTD , https://www.machineryxuanteng.com
Structure 1. The fan adopts centrifugal fan structure, large air volume, high wind pressure, noise elimination measures, and low noise during use.
2. The filter material of the single filter bag is selected 208 industrial polyester needle felt, the filter bag structure is a flat bag, each filter bag is equipped with a spring dust collector skeleton, the filtering effect is good, the replacement of the filter bag is convenient, and the service life is long .
3. The dust removing mechanism of the dust remover adopts an electric motor with an eccentric wheel to drive the connecting rod to shake the filter bag and remove dust on the outer surface of the dust filter bag. The cleaning mechanism has two types of automatic control and manual control; the automatic control means that the fans work continuously; the rapping and cleaning can be performed on demand; and after the manual control, that is, the fans stop, the cleaning mechanism automatically works and stops automatically after tens of seconds.
4. A spacious and sealed access door is installed on the single dust collector housing to facilitate the replacement of filter bags and the repair of internal components.
5. The single dust collector parts adopt the drawer type structure, which is convenient for operation and cleaning.
6.Single dust collector is equipped with dust gas inlet on one side, which can be used for dust collection equipment such as unpacking port, feed ash port, blasting tank, vibrating screen, crusher, bucket elevator and belt conveyor. And control (1) Working principle: Dust-laden gas is pumped into the box by the fan (installed in the upper part of the box) (entering from the middle or lower part of the box) and filtered by the bag. The dust is trapped on the surface of the filter bag and after purification The gas suction fan is discharged from the air outlet. The dust on the surface of the filter bag increases as the dust increases, the thickness of the filter bag increases, the resistance of the filter bag increases, and the dust removal efficiency decreases. In order to ensure efficient use of the dust collector, the dust accumulated on the surface of the filter bag must be removed. The PL dust collector is equipped with self-controlled dust removal. The device performs regular rapping to remove dust on the filter bag surface.
(2) Operation control: Connect the dust collector fan motor 1D and the dust removal motor 2D (J-type belt discharging motor 3D) to the electric control box, and then connect the 380V three-phase four-wire AC power supply with a control circuit of 220V. , And access to reliable ground.
PL type single dust collector
PL series single dust collector Introduction PL series single dust collector is a more advanced domestic dust removal equipment. PL single dust collector is a dust collection unit with small size, dexterous appearance and high dust removal efficiency. The basic structure of the dust removal equipment series consists of three components: blower, filter and dust collector. Each component is installed in a vertical frame, steel plate shell, baking paint anti-rust, beautiful appearance, scientific structure, reliable operation Easy to use. It is mainly suitable for the dust removal application of small-density non-fibrous dust, and the dust removal efficiency can be as high as 99.9%. The filter cartridge of the dust removal device is made of imported polyester fiber, and has the advantages of high dust removal efficiency, fine dust collection, small external dimensions, convenient installation and maintenance, long service life, and the like. During the operation of the equipment, due to the continuous deposition of dust on the surface of the filter cartridge in the filter, resistance is gradually formed, and saturation will soon be reached on the surface of the filter cartridge. When a certain saturation allowable resistance value is reached, the electronically controlled automatic pulse Backflush system for automatic cleaning. It is achieved by blowing compressed air. The filter cartridges are cleaned separately, so that a long period of air flow is ensured during the cleaning process, so the device can work for 24 hours in a row, and the dust removal effect is still very good.